Search Results for ‘torque’

I have 2011 LE and am trying to get transmission temperature from Torque app. I have tried to search the information regarding this, but I have only found the one for 2nd gen. sienna. Is there anyone who could tell me how to add up new PID on Torque? Thank you and Merry Christmas!

Hi, I have two questions for my 2006 Sienna 2WD. Q1 .I need new torque strut (dogbone) the one that is near the passenger side as it is cracked. The dealer is selling it for $65 but I can get it down to $45. RockAuto has Wester for $22.89, DEA for $24.79, Anchor for $24.99. Any suggestions here...

did a search and didn't find specifics. Anyone have the break job including rotors torque specs for 2012 XLE AWD. I think it is mainly just calliper bolts and lugs that I can think of. It is the first time doing them on the sienna. I am assuming it is similar to my 04 4Runner which I have done...

just changed the front catalytic converter. i need the torque for the manifold to the block and the cat to the pipe. thank you

What is the proper torque for the front wheel bearing on a 2008 Toyota Seinna when the bearing is replaced?

I am rebuilding the rear dif on my 09 Sienna. I normally buy an OEM shop manual for this sort of thing but last I checked it was a goo 300 buck or so. Can any one shoot me the specs for this thing. Input shaft nut bearing cap bolts rear cover bolts 3 mounting bolts in back, 2 on the side in...

Replacing the caliper and looking for the torque on 2006 Sienna brake hose banjo bolt? Not finding it online. thx

Hi All, I'm new here, but have been lurking for a bit. I recently purchased a '14 LE. I installed a Curt hitch and wiring harness along with an Airlift 1000 kit in preparation for towing our small pop-up camper (~2K loaded…yes I know I need trailer brakes and a controller…just haven’t done it...

First time post here.... I've got a 2006 Sienna LE. Oil pan gasket needs replacing b/c it's sprung a leak. Anyone know what the torque specs are for the pan bolts (not the plug) are when I replace the pan and new gasket? --kabj

Hi all: I just did the timing belt job on my 2004 Sienna at 108k miles. Changed the water pump, seals and idler pulleys along with it. The main complication was that one of the long engine mount bolts sheared off in place and drilling it out was a pain. This made it take a few days instead of...

Hello, I'm planning the front brake pad & rotor replacement of my 2011 Sienna LE FWD. If anyone knows, please let me know the torque spec below. 1. Caliper mounting bracket bolt 2. Guide pin bolt What I found on other web sites is 79 ft-lb & 25 ft-lb each for 2004 Sienna. But I'm not sure if...

We are having a little TQ shudder every once in a while. Fluid is good and clean. I've heard that there is an anti-slip additive that will cure this. Is it a Toyota product ?

08 sienna front axle nut torque? Hello new to the site, I have an 08 Sienna that needs front wheel bearings I was wondering if anyone new the torque spec for the axle nut. Also if anyone has any tips/tricks on making this job easier it would be appreciated. I'll be doing this with a buddy of...

Hi, I'll be changing a rear wheel bearing hub kit on my 2004 Sienna CE as soon the part comes in. I'm in need of the torque #'s! I've been carrying a few heavy loads recently and i'm sure this is what caused the premature wear on the rear bearing. Thx, ivanhoe

Ok so I've been doing some work on our 2004 LE FWD described in this thread installing an indicator lamp for the lockup clutch to see when it actually locks up: http://www.siennachat.com/forum/64-2004-2010-dec-2009-2nd-generation-toyota-sienna/13177-torque-converter-lockup-indicator.html After...

I was curious if there is an ECU or Transmission wire that controls the lockup of the torque converter that one might be able to tap into in order to run an LED light or something like that to show when the Torque converter lockup is commanded from the ECU? Also does anyone know if D is an...

Going to a 3x drain/fill on my transmission fluid soon as well as change the filter and add a magnefine filter to our 09 Sienna. I see the drain plug is 36 ft/lbs but cant seem to find the torque for the pan bolts. Also, do you tighten the pan bolts like a tire, across from each other and...

I've looked and looked, but does anybody know the exact torque specs for the transmission drain plug for the 2008 limited? Is 36 ft-lbs from the 2005 manual correct? I really like being precise. Thanks in advance. Gene

Hi All, First post here. I am always impressed with availability of expertise on these forums. My current project is to replace the lower control arms of my 04 Sienna XLE. I found some real good information on the process and pretty much already visualized the whole process including having...

I just found this dyno sheet on another site and was wondering: When pulling up a long steep hill is it best to keep the RPM where torque and HP intersect, at peak of Torque or peak of HP? Obviously I wouldn't want to run my motor at 5800 rpm, but what is the most efficient for discussion sake?